Hi Guys wanted to share my experience and create a 'How To Guide' for the removal and update/replacement of the newer style cup holder for the F25.
Now there was some trial and error the main part being there are 2 versions of this holder, one for RHD vehicles (PN 51169301723) and one for LHD (pn 51169301722) yes you guessed it i purchased the LHD version first, never noticed this, stripped down the centre console and then realised.
so make sure you order the right one, by the way if anybody needs the LHD version drop me a PM, more than happy to do a deal on this :)
Difficulty - Easy - just take your time
Time - 30-45 mins
Parts
Cup holder 51169301723 (RHD)
Cup holder 51169301722 (LHD - i have one spare)
Rubber insert, cup holder 5116930904 (fits both LHD/RHD)
Tools -
Torx T20
Flat Trim tool
Insulation tape
Small flat head screw driver
Also needed - Patience and marginal force
Original
[IMG]
[/IMG]
Ok so first step
Open up the arm rest and proceed to remove the trim around the gear shifter by popping the clips on each side. i sued a flat wide trim tool so as not to mark the softer trim underneath. Moderate force got this to move with no trouble.
[IMG]
[/IMG]
and here
then lift the trim up slowly, this will reveal the 3 connectors connecting the iDrive and other fittings on the trim.
now begin to unclip the connectors
here
here
and here
some of these were a little tight but gentle tug moved them all with little fuss.
leaving you with this, you should be able to see the clip points for the trim to work out where to pry etc..
and the back of the trim
now remove the small rubber insert at the bottom of the cup holder
revealing these bolts, you only need remove the centre one, T20 Torx bit
under the top rubber you should be able to see the push clips
and here
you need not do anything with these, just good to know how they look and how they release (pulling up) close up below of one
then remove the from lower plastic, again this just unclips by pulling down, used dry palm of hand to push down pop off. be careful here as there is the amber down light fixed to the back..
seen here
this simply unclips, do this carefully, observe the clips to see how it fits
then tuck the wire to the side out of the way so it doesnt trap the cup holder when removing
not the more strenuous bit, pull the rear of the cup holder up so it pops the rear clips
then lift the front section of the cup holder up, pay attention to each side, you will see location guides
Tricky part no 1. this part took a bit of giggling to get it to move, basically once the clips are free at the rear when you lift the front it leavers its self out of the slot, it does go with a pop (i almost thought i broken it)
Now undo the power connector which feed the 12v socket and led (note new socket doesn't illuminate )
and the new RHD cup holder
Mmmm i love the smell of new plastic in the morning lol
ok above you can see there is only 2 x wires on this unit, so we have to pop the pins out and put them in the old plug off the old 12v socket... here begins ...
tricky part No 2, using a small flat headed screwdriver, force down the side of each pin to close up the small metal clips that hold it in its socket. there is also a small plastic insert on the rear which needs to be popped out also, in theory you could actually cut these connector as you wont be using it again, or simply scotch block (electrical connector block the wires together in both sides and save about 10 mins, your call
once removed
both free
now grab the old cup holder and remove the pins from that connector, here there are 3 wires, the 3rd runs a small led which illuminates the 12v socket, this part of the connector will be redundant as there is no led on the newer unit (one hand gives, the other BMW hand takes away), i thought at this point you could possibly drill in a small 1/8" hole on the newer unit and reuse the led, simply mounting it with some super glue, this could work well (LED is same as the one pictured above in the from lower fascia) let me know if anyone tries this
the insert at the back
now discard the old unit and wires and grab the new cup holder wires and flick out the small metal retaining clips to hold into the connector once inserted..
small knife or Stanley blade does this quite well
as i'm not reusing the plastic insert i simply used some electrical tape to insulate it from the other wire in the connector, once done pop them into the old connector, matching up the wiring (brown to brown)
now we begin the revere of the install..
the unit sloted in quite easily, notice the clips either side that hang over the plastic lugs (note: these are not on the old holder) they caused no problem with the fit, in fact make it more stable and line the unit up
now remove the rear rubber on the new cup holder and line up the rear clips into the new holes (*note there are 4 holes on this new unit, i can only think this if for the change over year and/or X4) take your time here and make sure everything fits snug before popping it all back down
close up of holes/clips
little bit fiddly again locating things but take your time, and with a little force (again i thought id broken something) the unit just pops in place!
once in there is a little bit of movement, line up the hole and pop in the T20 screw ..
clearer picture of one of the side lugs/clips
refit the led and fascia
clip the 12v wire together, matching colours (colors for the Americans lol) like for like, (Note: only 2 wires in the new loom now )
now for the lower rubber insert
here
And fitted
now reverse the guide for clipping the wires back in and trim back on, everything should just pop back into place, with the odd pat of the palm of your hand to send the clips back home. again take your time line up the clips and don't forget to connect the 3 wires for the iDrive connector/parking break etc...
then sit back and admire your handy work
once completed, only you and fellow forum members will appreciate the monumental task you have just undertaken. wife or partner will not understand the sore fingers, scuffed knuckles, and money spent...best to say nothing and keep it on here :)
:cool!: hope you like the above...
it most certainly looks better, there is slightly less height on the back section as my sun glasses no longer fit, but this is fine as they can easily sit on top of the new draw...
good luck and let me know if any one want a LHD version :clap:
Now there was some trial and error the main part being there are 2 versions of this holder, one for RHD vehicles (PN 51169301723) and one for LHD (pn 51169301722) yes you guessed it i purchased the LHD version first, never noticed this, stripped down the centre console and then realised.
so make sure you order the right one, by the way if anybody needs the LHD version drop me a PM, more than happy to do a deal on this :)
Difficulty - Easy - just take your time
Time - 30-45 mins
Parts
Cup holder 51169301723 (RHD)
Cup holder 51169301722 (LHD - i have one spare)
Rubber insert, cup holder 5116930904 (fits both LHD/RHD)
Tools -
Torx T20
Flat Trim tool
Insulation tape
Small flat head screw driver
Also needed - Patience and marginal force
Original
[IMG]
Ok so first step
Open up the arm rest and proceed to remove the trim around the gear shifter by popping the clips on each side. i sued a flat wide trim tool so as not to mark the softer trim underneath. Moderate force got this to move with no trouble.
[IMG]
and here
then lift the trim up slowly, this will reveal the 3 connectors connecting the iDrive and other fittings on the trim.
now begin to unclip the connectors
here
here
and here
some of these were a little tight but gentle tug moved them all with little fuss.
leaving you with this, you should be able to see the clip points for the trim to work out where to pry etc..
and the back of the trim
now remove the small rubber insert at the bottom of the cup holder
revealing these bolts, you only need remove the centre one, T20 Torx bit
under the top rubber you should be able to see the push clips
and here
you need not do anything with these, just good to know how they look and how they release (pulling up) close up below of one
then remove the from lower plastic, again this just unclips by pulling down, used dry palm of hand to push down pop off. be careful here as there is the amber down light fixed to the back..
seen here
this simply unclips, do this carefully, observe the clips to see how it fits
then tuck the wire to the side out of the way so it doesnt trap the cup holder when removing
not the more strenuous bit, pull the rear of the cup holder up so it pops the rear clips
then lift the front section of the cup holder up, pay attention to each side, you will see location guides
Tricky part no 1. this part took a bit of giggling to get it to move, basically once the clips are free at the rear when you lift the front it leavers its self out of the slot, it does go with a pop (i almost thought i broken it)
Now undo the power connector which feed the 12v socket and led (note new socket doesn't illuminate )
and the new RHD cup holder
Mmmm i love the smell of new plastic in the morning lol
ok above you can see there is only 2 x wires on this unit, so we have to pop the pins out and put them in the old plug off the old 12v socket... here begins ...
tricky part No 2, using a small flat headed screwdriver, force down the side of each pin to close up the small metal clips that hold it in its socket. there is also a small plastic insert on the rear which needs to be popped out also, in theory you could actually cut these connector as you wont be using it again, or simply scotch block (electrical connector block the wires together in both sides and save about 10 mins, your call
once removed
both free
now grab the old cup holder and remove the pins from that connector, here there are 3 wires, the 3rd runs a small led which illuminates the 12v socket, this part of the connector will be redundant as there is no led on the newer unit (one hand gives, the other BMW hand takes away), i thought at this point you could possibly drill in a small 1/8" hole on the newer unit and reuse the led, simply mounting it with some super glue, this could work well (LED is same as the one pictured above in the from lower fascia) let me know if anyone tries this
the insert at the back
now discard the old unit and wires and grab the new cup holder wires and flick out the small metal retaining clips to hold into the connector once inserted..
small knife or Stanley blade does this quite well
as i'm not reusing the plastic insert i simply used some electrical tape to insulate it from the other wire in the connector, once done pop them into the old connector, matching up the wiring (brown to brown)
now we begin the revere of the install..
the unit sloted in quite easily, notice the clips either side that hang over the plastic lugs (note: these are not on the old holder) they caused no problem with the fit, in fact make it more stable and line the unit up
now remove the rear rubber on the new cup holder and line up the rear clips into the new holes (*note there are 4 holes on this new unit, i can only think this if for the change over year and/or X4) take your time here and make sure everything fits snug before popping it all back down
close up of holes/clips
little bit fiddly again locating things but take your time, and with a little force (again i thought id broken something) the unit just pops in place!
once in there is a little bit of movement, line up the hole and pop in the T20 screw ..
clearer picture of one of the side lugs/clips
refit the led and fascia
clip the 12v wire together, matching colours (colors for the Americans lol) like for like, (Note: only 2 wires in the new loom now )
now for the lower rubber insert
here
And fitted
now reverse the guide for clipping the wires back in and trim back on, everything should just pop back into place, with the odd pat of the palm of your hand to send the clips back home. again take your time line up the clips and don't forget to connect the 3 wires for the iDrive connector/parking break etc...
then sit back and admire your handy work
once completed, only you and fellow forum members will appreciate the monumental task you have just undertaken. wife or partner will not understand the sore fingers, scuffed knuckles, and money spent...best to say nothing and keep it on here :)
:cool!: hope you like the above...
it most certainly looks better, there is slightly less height on the back section as my sun glasses no longer fit, but this is fine as they can easily sit on top of the new draw...
good luck and let me know if any one want a LHD version :clap:
How To Guide - F25/26 Updated Cup Holder
0 commentaires:
Enregistrer un commentaire